AN1025 - Using HOTLink® with Long Copper Cables
AN1025 covers special characteristics and concern of operation with long copper cable using HOTLink® Overview The use of HOTLink® data communications products to drive copper media is documented in a...
View ArticleClik here to view.
AN56581 - PowerPSoC®– Designing LED Driver Circuits for MR-16 Lamps with...
The document describes a standard MR16 lamp with integrated LED driver. It gives an overview of the PowerPSoC family of controllers, specifications of the device used in this solution and a brief...
View ArticleAN69211 - Using High-Density Programmable FIFO In Video And Imaging Applications
AN69211 explains how to use Cypress high-density programmable FIFOs in video and imaging applications and the benefits offered over conventional FPGA and DDR SDRAM solutions. This information is...
View ArticleAN4059 - Clocking Options When Using HOTLink II™ Devices in HD-SDI...
AN4059 discusses the various clocking options that can be used in these applications when using the HOTLink II device.This application note focuses on HD-SDI applications at the 1.485 Gbps....
View ArticleAN1055 - Termination and Biasing of HOTLink II™ High-Speed Serial I/O
AN1055 discusses high speed circuit termination techniques and the required DC-biasing for the serial drivers and receivers used in the HOTLink II™ device. Introduction This application note is one of...
View ArticleAN1077 - Replacing Wire with Inexpensive Plastic Fiber Solutions
AN1077 explains the advantages of low cost fiber-optic solution and ways to implement it using Cypress CY7B923/CY7B933 HOTLink transceivers. Introduction Communication with fiber-optics has many...
View ArticleAN89371 - Power Saving With Cypress’s 65-nm Asynchronous PowerSnooze™ SRAM
This application note explains the PowerSnoozeTM feature of Cypress’ 65-nm Asynchronous Fast SRAM devices (CY7S10xxG family). PowerSnooze allows the SRAM to enter into a low-power mode during long...
View ArticleAN1125 - Interfacing the CYS25G0101DX to Differential LVPECL
AN1125 demonstrates how to connect the single-ended interface of CYS25G0101DX to a differential LVPECL device and provides simple formulas to help users calculate the values of the termination...
View ArticleClik here to view.
AN60685 - Interfacing the Cypress Powerline Communication Solution to CyFi™...
AN60685 describes a firmware project that bridges powerline communication (PLC) across different electrical phases using an Artaflex AWP24S CyFi™ radio frequency (RF) module. This wireless...
View ArticleAN35159 - TAXI™ to Cypress CY7C9689 HOTLink® Transceiver Conversion Series...
AN35159 shows the design considerations when interfacing to the serial inputs and outputs of the CY7C9689. Introduction The Cypress CY7C9689 HOTLink® Transceiver integrates all the functions necessary...
View ArticleClik here to view.
AN56778 - PowerPSoC®– MPPT Solar Charger with Integrated LED Driver
The Maximum Power Point Tracking (MPPT) algorithm is used in solar applications to track the peak power delivered by a solar panel and maximize the energy harvested by the panels. AN56778 describes...
View ArticleAN49081 - Requirements for Input Clock to West Bridge® Devices
AN49081 addresses the requirements for the input clock to West Bridge® devices that includes Antioch™, Astoria™, and TX3LP18. The conversion of phase noise specifications into equivalent RMS jitter is...
View ArticleAN1032 - Using Decoupling Capacitors
AN1032 provides recommendations on the use of decoupling capacitors for the HOTLink family of data communication products. Introduction Network analysis is used to prove that the conventional...
View ArticleAN1161 - HOTLink® Jitter Characteristics
AN1161 describes the basics of jitter in transmission systems, using HOTLink™ as the example, it shows how it can be analyzed and measured. Specific characterization data is presented to allow system...
View ArticleAN48864 - Optimizing Performance Using West Bridge® Controllers with Turbo-MTP
AN48864 discusses West Bridge® Turbo-MTP, which is a West Bridge specific implementation of Microsoft® Media Transfer Protocol (MTP). Mobile handsets and portable media devices seek compliance with...
View ArticleAN65974 - Designing with the EZ-USB® FX3™ Slave FIFO Interface
AN65974 describes the synchronous Slave FIFO interface of EZ-USB FX3. The hardware interface and configuration settings for the FLAGs are described in detail with examples. The application note...
View ArticleAN92577 - Migrating from FM25H20 to FM25V20A
AN92577 compares the key features of FM25H20 and FM25V20A. FM25H20 is now “Not recommended for new designs” and this application note explains how FM25V20A is a drop-in replacement for FM25H20....
View ArticleAN94020 - Getting Started with PRoC™ BLE
AN94020 introduces you to PRoC™ BLE, an ARM® Cortex™-M0 based programmable radio-on-chip with Bluetooth Low Energy. It explores the PRoC™ BLE solution and development tools and shows you how to create...
View ArticleAN91445 - Antenna Design Guide
AN91445 explains antenna design in simple terms and recommends two Cypress-tested PCB antennas that can be implemented at a very low cost for use with the Bluetooth Low Energy (BLE) solutions that are...
View ArticleAN1043 - Understanding Synchronous Dual Port RAMs
AN1043 discusses the basic features, operation, and expansion configurations of synchronous dual port SRAMs. A brief note on applications of synchronous dual port SRAMs is also included. Introduction...
View Article