AN67442 - SPI Implementation Using SerialMode-0 Of EZ-USB FX2LP™
This application note describes the implementation of serial peripheral interface (SPI) protocol using the FX2LP UART port in serial mode 0. This demonstration uses FX2LP as the SPI master for...
View ArticleAN58764 - Implementing a Virtual COM Port Using FX2LP™
Introduction The Cypress EZ-USB® FX2LP™ is a Hi-Speed USB peripheral controller. The programmability and flexibility of FX2LP allows you to implement USB device classes such as the Communication...
View ArticleAN86526 - PSoC® 4 I2C Bootloader
Introduction Bootloaders are a common part of MCU system design. A bootloader makes it possible for a product's firmware to be updated in the field. At the factory, initial programming of firmware...
View ArticleAN2168 - PSoC® 1 - Understanding Switched Capacitor Filters
A filter is a device that passes or rejects certain frequencies of a signal. Four common types of filters are: Low Pass Filters Band Pass Filters High Pass Filters Notch Filters This Application note...
View ArticleAN87391 - PSoC® 4 Segment LCD Direct Drive
PSoC 4 offers a patent pending digital correlation LCD drive mode, very low power consumption, and provides a complete user interface and system solution. Using example projects, this application note...
View ArticleClik here to view.
AN89346 - PSoC® 4 Intelligent Fan Controller
Project Device PSoC Creator Version Development Kit CY8CKIT-xxx Compiler Architecture Silicon Revision V3.0 CP7 or higher V2.2 SP1 or Lower 042 DVK 001 DVK Keil GCC MDK RVDS AN89346.zip PSoC 4 Prod...
View ArticleAN73052 - Configuring HX2VL Parameters
The content of this application note is now available in AN72332 - Guidelines on System Design using Cypress' USB 2.0 Hub (HX2VL)
View ArticleAN72428 - Schematic Review Checklist for WirelessUSB™ NL
Introduction WirelessUSB NL enables a Gaussian frequency-shift keying (GFSK) radio by using a differentiated single-mixer, closed-loop modulation design that optimizes power efficiency and...
View ArticleAN76405 - EZ-USB® FX3 Boot Options
Introduction EZ-USB® FX3 is the next generation USB 3.0 peripheral controller, providing highly integrated and flexible features that enable developers to add USB 3.0 functionality to a wide range of...
View ArticleAN76348 - Differences in Implementation of EZ-USB® FX2LP™ and EZ-USB FX3...
Through the use of several example applications, you learn about the differences between FX3 and FX2LP at the architectural, hardware level, and firmware framework levels. Introduction Cypress EZ-USB...
View ArticleClik here to view.
AN2163 - Interfacing to 1-Wire/Two-Wire Digital Temperature Sensors using...
This application note also illustrates how PSoC® 1 can be used for sensing temperature using a DS18S20 (1-wire digital temperature sensor) and a TMP75 (Two-Wire digital temperature sensor) along with...
View ArticleAN6075 - enCoRe™ II USB Bootloader
Allowing end users to upgrade their products for bug fixes or feature enhancements is a desirable feature from both a marketing and engineering perspective. enCoRe™ II, as a Flash-based...
View ArticleAN61345 - Designing with EZ-USB FX2LP™ Slave FIFO Interface using FPGA
An FX2LP-FPGA interface is implemented to add High-Speed USB connectivity for FPGA based applications, such as data acquisition, industrial control and monitoring, and image processing. The FX2LP...
View ArticleAN68829 - Slave FIFO Interface for EZ-USB® FX3™: 5-Bit Address Mode
Introduction Cypress’s EZ-USB FX3 is the USB 3.0 peripheral controller, which allows developers to add USB 3.0 functionality to any system.
View ArticleAN75779 - How to Implement an Image Sensor Interface with EZ-USB® FX3™ in a...
Introduction The high bandwidth provided by USB 3.0 puts high demands on ICs that connect peripherals to USB. A popular example is a camera streaming uncompressed data into a PC. In this application...
View ArticleAN70707 - EZ-USB® FX3™/FX3S™ Hardware Design Guidelines and Schematic Checklist
The Cypress EZ-USB FX3 is the next generation USB 3.0 peripheral controller. With its highly integrated and flexible features, developers can add USB 3.0 functionality to any system. All...
View ArticleAN65209 - Getting Started with FX2LP™
Introduction The Cypress EZ-USB FX2LP (hereafter abbreviated as FX2LP) is a flexible USB 2.0 peripheral controller designed to handle maximum USB 2.0 bandwidth. To take full advantage of the USB 2.0...
View ArticleAN5004 - HD-SDI and SD-SDI SMPTE Jitter Performance of the Independent...
Introduction The HOTLink II™ family of physical layer (PHY) devices is a point-to-point or point-to-multipoint communications building block that provides serialization, deserialization, optional...
View ArticleAN91378 - HX3 Hardware Design Guidelines and Schematic Checklist
AN91378 provides hardware design and PCB layout guidelines for HX3, a high-performance USB 3.0 hub. These guidelines will help to ensure best performance with respect to signal integrity and full...
View ArticleAN108 - Differences between FM18L08 and FM28V020
Introduction The FM28V020, a 256-Kbit parallel F-RAM, is a replacement device for FM18L08; FM18L08 is now obsolete. For most designs, the FM28V020 device can be considered equivalent or better than...
View Article